Easy to incorporate legendary syringe pump technology into your equipment
Ideal high force syringe pump for do-it-yourselfers and OEM equipment designers
Precisely dispenses volumes at high pressure
Three modes of operation:
Constant flow rate
Quantity discounts available on request
The High Pressure Programmable Pump Module model provides full programmability along with Infuse/Withdraw capability. This unit is designed to operate inside an enclosure, cabinet, or on top of a bench. The board may be removed for “remote” operation.
Pressure and Speed The High Pressure Pump Module can deliver up to 220.82ml/minute with a single 140ml syringe. Maximum pressure is dependent on syringe size. Drive produces >200 lbs linear force.
Infusion and Refill Rates Specify independent rates for infusing and refilling. This allows a slow infusion rate then a fast refill.
Target Volume Specify the volume that is to be infused or refilled. The pump will run at the rate specified until this volume has been delivered when in the Volume mode.
Auto Fill Auto Fill automatically activates an externally attached solenoid (refer to Appendix L for part number) and refills the syringe when it is empty. This permits infusions to be virtually independent of syringe capacity.
Modes of Operation (Set for pump mode, can be changed thru RS-232) Pump: Runs continuously in the infuse or refill directions until stopped. Volume: Runs until a specified volume has been pumped or refilled. Program: Pump operates according to specified sequence of instructions. (Note: All modes interact with Auto Fill)
External Connections User I/O Allows pump operations to be synchronized with external devices or by a person at a distance from the pump. Connector pins are available to control direction of pump travel to control an external valve for refilling, and for general use. A simple contact closure to ground or TTL level signals may be used for inputs.
RS-232 Multiple pumps can be ‘daisy chained’ together and remotely controlled from a computer or any device communicating via RS-232.
Stall Detection An optical detector is used to verify expected movement of the motor. If the motor is prevented rfom turning due to jamming or excessive back pressure, the pump will stop.
Program Storage Programmable model can store up to 4 sets of 9 program sequences for later selection.
Infuse Rate The Infuse Rate is the rate of pumping while infusing in the Pump or Volume modes.
Target Volume The Target Volume is the volume that you desire to deliver at the set Infuse or Refill Rate.
Auto Fill When set to ‘ON’, the syringe is assumed to be empty. Auto Fill continuously monitors the volume of the syringe according to the volume pumped. When the pump determines that the syringe is empty, the operation in progress is suspended and Auto Fill is activated. The pumping direction is then reversed and the pump runs at the refill rate.
Program Description The programming functions of this pump provide powerful capabilities for advanced experiments. While in program mode this pump can perform the following tasks at a predetermined time or when prompted by a signal from an external device:
Start or stop pumping
Change pumping direction (infuse-withdraw)
Change flow rates
pump a precise volume and stop
Ramp up or down flow rates
In program mode the above tasks can be linked together into powerful programs to simplify your automation projects.
This Pump Module is supplied complete with the following components: Component Quantity Main Unit 1 Motor/Encoder Extension Cable, 6 ft. 1 DC Power Extension Cable, 6 ft. 1 RS-232 Cable 1
70-2202 High Pressure Syringe Pump Module
# of Syringes
Average Linear Force
Cable Length English
DC Power 4-pin Header (Friction Lock – Molex or AMP) RS-232 4-pin RJ-11 Telephone Jack User I/O 9-pin D-Sub Female
Control Board Mounting Holes
Mounting holes for (4) #6 screws
Control Board Mounting Length English
Control Board Mounting Length Metric
Control Board Mounting Width English
Control Board Mounting Width Metric
Optional 2x20 Line VFD (p/n 2400-235)
Constant Current (Chopper) Drive, 2A per phase (max.), microstepping (from 1/2 to 1/32)